- Product Describe
-
I. Introduction
This instrument is essential for conducting flexural strength tests on mortar-cement specimens; it can also be used to test the flexural strength of other types of cement and other non-metallic brittle materials.
II. Main Technical Parameters
Maximum test force
1000 N with a single lever
5000 N with dual levers
Indication accuracy ±1%
Single-lever force ratio of 10:1
Dual-lever force ratio of 50:1
Loading rate: 50 N/sIII. Structural Overview
The electric flexural testing machine consists of the following components (as shown in the figure):
1. The main lever ⑻ is made of 45 steel plates, with scale markings engraved on its surface; the left end is fitted with a mating cam ⑴, and the middle section is inlaid with a fulcrum blade ⑶ and a support blade ⑷.
2. The lead screw ⑸ is parallel to the main scale and is driven by a reversible motor to rotate, thereby causing the carriage ⑹ to move along the main scale.
3. The upright post ⑩ primarily serves a supporting function.
4. The secondary lever (23) primarily transmits the load applied to the primary bending blade to the secondary bending blade (22) via the upper and lower clamping fixtures (15), thereby subjecting the test specimen to stress. When the stress exceeds the flexural strength of the cement, the specimen fractures, causing the positioning pin on the right side of the main lever to strike the microswitch (11), which in turn stops the motor.
5. The lower fixture is raised and lowered by turning the handwheel ⒃, which actuates the lifting screw ⒄.
IV. Installation
1. Unboxing the electric flexural testing machine:
⑴. Open the top cover of the shipping box and remove the plastic film cover.
⑵ Remove the primary and secondary levers, the main unit, and other components; strip off the packaging film; and perform cleaning and dust removal.
2. Environmental requirements for the installation location of the electric flexural testing machine:
⑴ The electric flexural testing machine shall be installed on a sturdy workbench, with an indoor temperature ranging from 17°C to 25°C.
(2) Prevent the ingress of water vapor and corrosive gases.
⑶ Installation of the electric flexural testing machine:
① Place the main body of the electric flexural testing machine on the workbench and ensure it is properly leveled.
② Mount the main lever assembly onto the bracket, connect it to the suspension assembly and the secondary lever, secure the baffle on the fixed knife holder, and then connect the power supply.
V. Operating Procedures and Usage Rules
1. Operating method:
⑴ Connect the power supply.
⑵ Adjust the zero point (adjust the counterweight so that the sliding weight is at the “0” position and the main lever is horizontal).
(3) Remove any adhering debris from the circular and irregular surfaces of the fixture, place the test specimen into the flexural testing fixture, and adjust the fixture to securely clamp the specimen, thereby creating an upward angle in the main lever (the magnitude of this angle is determined based on the number of days the specimen has been stored and operational experience).
(4) Press the start button; the indicator light will illuminate (green), driving the motor to rotate the lead screw and move the moving carriage to apply the load. When the load reaches a specified value, the test specimen will fracture, causing the positioning pin at the right end of the main lever to press down on the microswitch, which in turn stops the motor. At this point, the flexural strength value can be read directly from the main scale.
⑸ Press the button (7) on the sliding weight to return it to the “0” position, then read the flexural strength value.
2. Usage Rules:
Upon completion of the test, the power supply must be switched off and the sliding weight returned to the “0” position (fine adjustment can be made by rotating the lead screw to bring the sliding weight back to “0”).
VI. Maintenance and Troubleshooting of the Electric Flexural Testing Machine;
1. Maintenance of the electric flexural testing machine;
(1) The electric flexural testing machine shall not be used in environments containing corrosive gases or strong magnetic fields.
(2) The electric flexural testing machine is equipped with a dust cover; be sure to close it after use to prevent dust from entering.
(3) The blades and blade pads of the electric flexural testing machine shall be regularly wiped with a lint-free cloth dampened with anhydrous alcohol to prevent dust and oil from accumulating on the blade-contact surfaces.
2. General troubleshooting;
⑴ If the start indicator light does not illuminate, check whether the fuse has blown.
(2) If the main lever of the electric flexural testing machine swings inflexibly, check whether each blade is properly seated in the V-shaped blade support of the blade holder.
(3) If the float switch button malfunctions, check whether any screws in the float switch button assembly are loose or whether the spring has failed.
VII. Complete Set Overview of Electric Flexural Testing Machine
⑴ One set each of the main body and primary lever assembly, and one set of the secondary lever assembly for the electric flexural testing machine.
(2) One protective cover.
⑶ Spare parts ① One 1A fuse.
(4) One product manual.
⑸ One copy of the certificate of conformity
Company Profile
Hebei Yinfeng Experimental Instrument Co., Ltd. is a high-tech enterprise dedicated to the research and development, production, and sales of experimental instruments. The company is headquartered in Hebei Province, relying on the strong industrial foundation and technological innovation resources in the Beijing Tianjin Hebei region. It is committed to providing high-precision and high reliability testing equipment and solutions for material testing, engineering quality control, scientific research experiments and other fields.
Customized Delivery Process
We provide customers with full-process services ranging from pre-sale consultation, customized solution design, equipment installation and commissioning to after-sale technical support.
Online Communication
Provide Custom Drawings
Merchant Quotation
Sign A Contract
Processing And Production
Packaging And Distribution
Confirm Receipt Of Goods
Successful Transaction
Cement Electric Flexural Testing Machine
If you need customized products, Contact US !
Tag list
Request a Quote
We will contact you within one working day. Please pay attention to your email.
Related Products
Content update in progress