• Electric Hydraulic Punching Machine
  • Electric Hydraulic Punching Machine
Electric Hydraulic Punching Machine
Electric Hydraulic Punching Machine
+
  • Product Describe
  • The electric hydraulic punch is a specialized testing instrument designed for cutting various waterproof materials using hydraulic pressure, offering simple and convenient operation.

    Main Specifications and Technical Parameters

    1 Rate of ascent 50cm/min
    2 Large piston stroke 270mm
    3 Motor Specifications 1500W, 380V, 1400 rpm
    4 Film thickness 10-15mm
    5 High pressure during冲片 10 tons
    6 Net weight Approximately 210 kilograms

    Features of the Electric Hydraulic Punching Machine

    This machine is hydraulically driven, offering smooth, safe, and reliable operation, high efficiency, low noise, and a long service life.

    Structure and Operating Principle of the Electric Hydraulic Punching Machine

    This machine primarily consists of a main frame, a hydraulic system, and an electrical system.

    Rack assembly: primarily composed of cross beams, upright columns, pallets, hydraulic cylinders, an outer casing, and a base.

    Hydraulic System: The system consists of a hydraulic pump, directional control valves, an oil tank, oil filters, and hydraulic hoses and fittings. The hydraulic pump is an axial piston high-pressure pump with a flow rate of 2.5 m³/min and a rated pressure of 31.5 MPa, directly driven by a 1,500 kW three-phase motor and mounted on a base.

    The changeover valve is mounted on the right side of the front panel and is operated by a manual lever. Lifting the lever raises the cylinder, pressing it down lowers the cylinder, and holding it in the middle position stops the cylinder.

    The relief valve is installed inside the housing. The relief valve is used to regulate the pressure range; this setting has been properly adjusted at the factory and must not be altered arbitrarily.

    Operating Instructions for the Electric Hydraulic Punching Machine

    Before use, first fill the hydraulic oil tank with 6 liters of hydraulic oil (add oil by opening the rear cover), then check that all relevant fittings and fasteners are securely tightened; if any are loose, tighten them immediately to prevent oil leakage and ensure proper operation. Also, verify that the electrical system is properly grounded and that the fuses are functioning correctly.

    Operating Procedures and Methods

    To begin, move the manual lever to the neutral (stop) position, then press the start button on the control panel to energize the system. The oil pump will then activate. Manually operate the lever to raise the piston by a short distance, and carefully observe for any signs of jamming or other abnormalities. If such issues are detected, immediately stop the machine, perform a thorough inspection, and eliminate the problem. If no abnormalities are found, continue raising and lowering the piston several times to purge all air from the cylinder. Once no air bubbles are visible in the hydraulic lines, the equipment is ready for normal operation.

    Maintenance and Servicing of Electric Hydraulic Punching Machines

    The instrument should be kept clean both inside and out to prevent rusting of its various components.

    Regularly inspect the hydraulic fluid for cleanliness. Depending on operating conditions, the hydraulic fluid in the reservoir should be allowed to settle once a month, and the fluid should be replaced every six months. When changing the fluid, thoroughly clean the reservoir and the oil filter. If the fluid is found to be cloudy or severely contaminated and no longer suitable for use, it should be replaced promptly; otherwise, wear on the hydraulic components will accelerate, potentially even disrupting normal operation. The recommended specifications for hydraulic fluid vary with ambient temperature as follows:

    When the ambient temperature is 15±5°C, use GB443-84 N46 (equivalent to No. 30 mechanical oil).

    When the ambient temperature is 25±5°C, use GB443-84 N68 (equivalent to No. 40 hydraulic oil).

    Precautions for Electric Hydraulic Punching Machines

    1. It is strictly prohibited to operate the oil pump without lubrication, causing it to run dry.

    2. Before use, all air must be purged from the system.

    3. When performing punch-forming tests, pay close attention to the stroke of the hydraulic cylinder; ensure that the piston does not come into contact with the test specimen to prevent damage to the equipment. Operators must exercise particular caution.

    4. After completing the test, the piston should be lowered to the bottom to prevent moisture from causing rust.

    5. The operating manual must be read before using the testing machine.

Company Profile

Hebei Yinfeng Experimental Instrument Co., Ltd. is a high-tech enterprise dedicated to the research and development, production, and sales of experimental instruments. The company is headquartered in Hebei Province, relying on the strong industrial foundation and technological innovation resources in the Beijing Tianjin Hebei region. It is committed to providing high-precision and high reliability testing equipment and solutions for material testing, engineering quality control, scientific research experiments and other fields.

Plant
Factory environment
Workshop
Workshop environment

Customized Delivery Process

We provide customers with full-process services ranging from pre-sale consultation, customized solution design, equipment installation and commissioning to after-sale technical support.

Online Communication

Provide Custom Drawings

Merchant Quotation

Sign A Contract

Processing And Production

Packaging And Distribution

Confirm Receipt Of Goods

Successful Transaction

  • Electric Hydraulic Punching Machine
  • Electric Hydraulic Punching Machine
Electric Hydraulic Punching Machine
Electric Hydraulic Punching Machine
+

Electric Hydraulic Punching Machine

The electric hydraulic punch is a specialized testing instrument designed for cutting various waterproof materials using hydraulic pressure, offering simple and convenient operation.

If you need customized products,  Contact US !

Share to

Request a Quote

We will contact you within one working day. Please pay attention to your email.

Related Products

Content update in progress

Request Quote

We will contact you within one working day. Please pay attention to your email.

SUBMIT