- Product Describe
-
Product Introduction
The helmet impact and puncture testing instrument is designed and manufactured in accordance with the new national standards GB/T 2812-2006 and GB 2811-2007 for safety helmets. It is used to test the impact absorption performance and puncture resistance of safety helmets and is widely employed by supervisory inspection stations for special labor protective equipment, research institutes of construction science, construction project quality inspection stations, and safety-helmet manufacturers, among others.
Technical Specifications
Parameter Category
Parameter Metrics
Product Model
SDM-03
Operating Power Supply (V/Hz)
220V, 50Hz, 50W
Impact hammer
Mass: 5–5.01 kg; hammer head is hemispherical with a radius of 48 mm; material: 45# steel.
Steel, with a symmetrical and uniform appearance.
Puncture cone
Mass: 3–3.05 kg; cone angle: 60°; cone tip radius: 0.5 mm; conical
Length: 40 mm; maximum diameter: 28 mm; hardness: HRC 45
Dynamic sensor
0–20 kN, frequency 5 kHz
Test accuracy
≤2.5%
Display resolution
1N
Impact penetration height
1000 mm ± 5 mm, adjustable
Adapt to standards
GB/T 2812-2006 “Test Methods for Safety Helmets” and GB 2811-2007 “Safety Helmets”
Random Attachment
One head form each for No. 1 and No. 2, one impact hammer, and one puncture cone (including the puncture wire).
One power cord.
Other items are listed on the packing list.
Operating Steps
Impact Absorption Performance Test
1. Connect the power supply and turn on the instrument’s power switch. The power indicator light should illuminate, and the instrument must be allowed to warm up for at least 10 minutes.
2. Place the pre-treated safety helmet correctly on the headform, ensuring that the helmet band is in natural, stable contact with the headform, and then close the protective guard door. (If the displayed force value is not zero at this point, press the “Zero” key to reset the instrument reading to zero.)
3. Place the upper surface of the falling hammer on the lower surface of the electromagnetic device, then press the “Engage” button. The electromagnetic engaging mechanism will activate, thereby holding the falling hammer in place.
4. Use a standard steel ruler to measure the distance from the bottom of the drop hammer to the top of the safety helmet. If this distance does not meet the requirement of 1000 mm ± 5 mm, manually make fine adjustments to the vertical position of the drop hammer using the handwheel on the right side of the instrument until the specified tolerance is achieved. (To save time and ensure the test is completed within 30 seconds, the height can be adjusted to the correct setting before pre-treating the safety helmet.)
5. Press the “Release” button to deactivate the electromagnetic holding device, allowing the falling hammer to drop freely and strike the top of the safety helmet. At the same time, the impact force value is displayed at its maximum and then latched.
6. Record the value displayed on the impact-force meter; this represents the maximum impact force that the safety helmet can withstand. Open the guardrail door, remove the safety helmet and the falling hammer, and inspect the helmet’s surface for any possible damage.
7. Repeat steps 2 through 6 as necessary until all test specimens have been tested.
8. Upon completion of the test, turn off the instrument power, properly store the head form and impact hammer, and perform equipment maintenance and servicing.
Company Profile
Hebei Yinfeng Experimental Instrument Co., Ltd. is a high-tech enterprise dedicated to the research and development, production, and sales of experimental instruments. The company is headquartered in Hebei Province, relying on the strong industrial foundation and technological innovation resources in the Beijing Tianjin Hebei region. It is committed to providing high-precision and high reliability testing equipment and solutions for material testing, engineering quality control, scientific research experiments and other fields.
Customized Delivery Process
We provide customers with full-process services ranging from pre-sale consultation, customized solution design, equipment installation and commissioning to after-sale technical support.
Online Communication
Provide Custom Drawings
Merchant Quotation
Sign A Contract
Processing And Production
Packaging And Distribution
Confirm Receipt Of Goods
Successful Transaction
Previous:
Next:
Reaction Frame
If you need customized products, Contact US !
Category
Tag list
Request a Quote
We will contact you within one working day. Please pay attention to your email.
Related Products
Content update in progress