• Coarse-Grained Soil Relative Density Tester
  • Coarse-Grained Soil Relative Density Tester
  • Coarse-Grained Soil Relative Density Tester
  • Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
+
  • Product Describe
  • The electric relative density meter is manufactured by our factory in accordance with the “Geotechnical Testing Procedures” SL237-1999 and the “Highway Geotechnical Testing Procedures” JTJ051-93. It is intended for use with non-cohesive soils and sands having particle sizes less than 5 mm, provided that the mass of samples with particle sizes between 2 and 5 mm does not exceed 15% of the total sample mass. The instrument is used to determine the maximum dry density and the minimum void ratio of the soil, which are then employed to calculate its relative density.

    Main components of the soil relative density meter: The instrument consists primarily of a housing, control panel, transmission mechanism, measuring cylinder, vibrating hammer, and other components.

    Technical Specifications

    1 Metal container 250 ml, inner diameter 5 cm, height 12.7 cm, with protective sleeve
    2 Hammer Hammer mass: 1.25 kg; drop height: 15 cm; hammer diameter: 5 cm; frequency: 32 cycles/min.
    3 Vibration hammer 155 times/min
    4 Timing Range 0–15 minutes
    5 Power 120W
    6 Power supply 220V 50HZ
    7 Net weight of product 40KG

    Instrument Installation

    1. Upon unpacking, verify the contents against the packing list.
    2. Place the instrument on a level cement floor and check whether the positioning plate is loose; if it is, tighten it with a wrench. Lift the hammer rod, place a wooden shim in the specimen cylinder, and then lower the hammer rod.
    3. Plug in the power cord, press the power switch on the right side of the instrument, set the timer for 1–2 minutes, and then press the start switch to begin operation.

    Method of Use for the Electric Soil Relative Density Meter

    1. Plug in the power cord and turn on the power switch on the right side of the instrument.
    2. Lift the rammer until the locking pin is fully inserted, ensuring that the rammer does not drop. At this point, loosen the locking screws on both sides of the metal container, remove the container, and load the soil sample in accordance with the specified procedures. Push the container into the positioning plate and tighten the locking screws. Then, holding the rammer with one hand and pulling out the locking pin with the other, slowly lower the rammer.
    3. Turn on the power switch, and the instrument will enter the ready-to-operate state.
    4. Turn the timer to the desired time setting, and the instrument will start operating.
    5. Upon completion of the test, calculations shall be performed in accordance with the “Geotechnical Testing Procedures” (SL237–99) and the “Relative Density Test” method (SL237–010–99).
    6. After compaction is completed, lower the hammer, loosen the locking screw, and then remove the metal container and the protective sleeve.
    7. After the test is completed, clean any remaining soil from the instrument, turn off the power switch, unplug the power cord, and cover the instrument with the dust cover.

    XD-1 Soil Relative Density Tester:
    The purpose of the instrument test is to determine the maximum and minimum void ratios of non-cohesive soils, which are used to calculate the relative density and thereby assess the soil’s degree of compaction in its natural state or after compaction, as well as the stability of its particle structure.

    Technical Specifications

    1. Graduated cylinders: capacities of 500 cm³ and 100 cm³  https://assets.alicdn.com/kissy/1.0.0/build/imglazyload/spaceball.gif

    2. Long-necked funnel: inner diameter of the neck tube 1.2 cm  https://assets.alicdn.com/kissy/1.0.0/build/imglazyload/spaceball.gif

    3. Volume: 250 cm³; inner diameter: 5 cm; height: 12.7 cm; volume: 1000 cm³

Company Profile

Hebei Yinfeng Experimental Instrument Co., Ltd. is a high-tech enterprise dedicated to the research and development, production, and sales of experimental instruments. The company is headquartered in Hebei Province, relying on the strong industrial foundation and technological innovation resources in the Beijing Tianjin Hebei region. It is committed to providing high-precision and high reliability testing equipment and solutions for material testing, engineering quality control, scientific research experiments and other fields.

Plant
Factory environment
Workshop
Workshop environment

Customized Delivery Process

We provide customers with full-process services ranging from pre-sale consultation, customized solution design, equipment installation and commissioning to after-sale technical support.

Online Communication

Provide Custom Drawings

Merchant Quotation

Sign A Contract

Processing And Production

Packaging And Distribution

Confirm Receipt Of Goods

Successful Transaction

  • Coarse-Grained Soil Relative Density Tester
  • Coarse-Grained Soil Relative Density Tester
  • Coarse-Grained Soil Relative Density Tester
  • Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
Coarse-Grained Soil Relative Density Tester
+

Coarse-Grained Soil Relative Density Tester

The electric relative density meter is manufactured by our factory in accordance with the “Geotechnical Testing Procedures” SL237-1999 and the “Highway Geotechnical Testing Procedures” JTJ051-93. It is intended for use with non-cohesive soils and sands having particle sizes less than 5 mm, provided that the mass of samples with particle sizes between 2 and 5 mm does not exceed 15% of the total sample mass. The instrument is used to determine the maximum dry density and the minimum void ratio of the soil, which are then employed to calculate its relative density.

If you need customized products,  Contact US !

Share to

Request a Quote

We will contact you within one working day. Please pay attention to your email.

Related Products

Content update in progress

Request Quote

We will contact you within one working day. Please pay attention to your email.

SUBMIT